- Outdoor Condenser: RIO09HP230V1BO
- Indoor Wall Mounted Air Handler: RIO09HP230V1BH
- Wireless Remote Control
- Required, but not included: 1/4" x 3/8" line set
High Efficiency G-10 Inverter
The G10 Inverter uses a broad range of variable frequencies to drive the compressor, marking the highest level of inverter control technology available today. Unlike conventional technology that generally regulates room temperature by running at maximum capacity and then shutting off completely, G10 Inverter technology eliminates these harsh starts/stops. This cutting edge functionality results in quicker arrival at desired temperatures and superior maintenance of consistent comfort levels.
Not only is the Rio system energy efficient, it's quiet too. Wall mounted units operate with sound levels starting as low as 32 dB(A).
The Intelligent Defrost function increases room comfort and saves energy by eliminating unnecessary defrost cycles. In heating mode, the control system monitors the outdoor coil for frost buildup, and the system switches to defrost mode only when frost buildup is actually detected. This avoids unnecessary and wasteful defrosts.
Low Voltage Start Up
Having stable electrical power is not always an option. This GREE system will operate from 170v to 253v, which is suitable for unstable power supply areas.
The system guards against the annoying cold blow in heating mode, and constantly monitors the discharge air temperature. It will delay the indoor fan until the indoor coil has warmed up to prevent blowing uncomfortable cool air into the room.
Features & Benefits:
- Compact and Quiet Design
- High Efficience - 16 SEER
- DC Inverter Technology
- Wireless Remote with LCD Display
- Low Ambient Cooling
- Comfortable Sleep Mode
- Intelligent Defrost
- 5 Year Limited Parts Warranty
- 7 Year Limited Compressor Warranty
Please Note: Mini Split Systems must be installed by a licensed Contractor with an EPA Refrigerant Certification to qualify for warranty.
Which line set kit do I need?
This system uses a 1/4" x 3/8" line set. These are sold separately, and you can choose from our 15 ft, 25 ft, and 50 ft lengths. The length needed depends on the needs of your project and how you will set up the system (distance from outdoor condenser to indoor air handler).
Can I install this myself?
While installation of a ductless split is much easier than a central air system, it's still much more advanced than installing a window unit or portable. Furthermore, the manufacturer warranty is only valid if a licensed professional does the installation. So while it is possible to do the installation yourself, we strongly recommend you hire an HVAC professional in your area.
Is this backed by a warranty?
Yes, it comes fully backed by a manufacturer's warranty, and ComfortUp is an authorized online seller of these systems. Our Customer Care team will provide assistance should you ever need to file a warranty claim with the manufacturer. Please be aware that only systems that are installed by a licensed HVAC contractor are backed by the warranty. Proof of licensed installation is required. The receipt/invoice from your contractor should be sufficient.
|Equipment Type||Heat Pump|
|EER (Energy Efficiency Ratio)||10.6|
|HSPF (Heating Seasonal Performance Factor)||8.5|
|Rated Cooling Capacity (BTU)||9,000|
|Rated Heating Capacity (BTU)||9,000|
|Warranty Offered||7 Year Compressor - 5 Year Parts to Original Registered End-User with Proof of Proper Installation|
|Energy Star Rated||No|
|Maximum Cooling Capacity||11,500|
|Nominal Capacity (BTU)||9,000|
|Maximum Heating Capacity||13,500|
|Minimum Heating Capacity||3,400|
|4-Way Remote Air Flow Control||No|
|Liquid/Gas Line Set Size||1/4" X 3/8"|
|Minimum Circuit Amps||20|
|Sound Pressure Rating||26 dB(A)|
|Maximum Fuse Size||15|
|Number of Zones/Rooms||Single|
|Mounting Type||Wall Mount|
|Minimum Cooling Capacity||3,800|
|COP (Coefficient of Performance)||3.4|
REMOTE CONTROLLER OPERATIONS
Theriouniversal wireless remote controller is sleek, versatile and allows you to changeroom temperatures and functions on unit from the palm of your hand. The large LCD display and buttons make it easy-to-understand and easy-to-use.
The remote controller may be used for severalriounits.It can operate the unit from a distance of up to 25 ft. (7.6 m) as long as there are no obstructions. This is one-way communication only (from remote controller to indoor unit.)
The remote controller is set from factory to display temperatures in°F. If °C is desired, turn the remote OFF and then press “MODE“ and “––” buttons on the remote simultaneously
NOTE: Not every unit has each of the functions described below. If your unit does not come equipped with a certain function, the button will be inactive
Pressing this button will turn the unit on and off. Using the ON/OFF function will cancel TIMER and SLEEP functions, but preset times will not be affected.
Pressing this button will present the AUTO, COOL, DRY, FAN and HEAT mode options which can then be selected. AUTO mode is the default mode. When the indoor unit first powers on under this mode, the temperature will not be displayed.
Pressing this button will present the AUTO, LOW, MEDIUM, and HIGH speed optionswhich can then be selected. .Low .Medium .High
NOTE: When the indoor unit first powers on, the AUTO fan speed is the default mode. In DRY MODE, the fan will automatically run at low speed.
Do not drop or throw remote controller
Protect remote controller from water
Keep remote controller away from direct sunlight or high heat
REMOTE CONTROLLER FUNCTIONS
Press the LIGHT button to turn On or Off the display on the indoor unit frontpanel. When the indoor unit first powers on, the front panel display will default to ON. The LIGHT icon will display when the front panel display is ON.
Press the TURBO button to reach the desired room temperature faster. After selecting the “HEAT” or “COOL” mode button, push the “TURBO” button. This will force the unit to run at ultra high speed. When TURBO mode is running,the TURBO icon is displayed on the remote controller.
Press the X-FAN button to allow the indoor fan to run for 10 minutes after the unit is turned off (cooling or dry modes only) to ensure that additional moisture is removed from coil. X-FAN icon will be displayed on remote controller.
Press the + button to raise the room setpoint. Press once for slow adjustment and hold down for fast adjustment.
Press the –button to lower the room setpoint. Press once for slow adjustmentand hold down for fast adjustment.
Press the TIMER button to activate TIMER mode and the HOUR ON/OFF icon willbegin blinking. Pressing + or - button changes time setting from 0.5 to 24 hours. Press TIMER button to confirm settings.
Press this button to select either Room Setpoint, Room Temperature or Outdoor Temperature on the indoor unit front panel display. The front panel display will always revert to room setpoint after 5 seconds. When the indoor unit first powers on it will display the room setpoint setting. Look for the “thermometer” icon to appear inside or outside the ”house” icon on the remote controller display, indicating whether the front panel is displaying room setpoint, indoor or outdoor temperatures.
Press the SLEEP button to activate SLEEP function and select one of three comfortable SLEEP modes. The SLEEP icon will be displayed.
VERTICAL SWING LOUVER
Press the button to adjust the direction of airflow in the room. By moving the louvers up or down, you can control the air for maximum comfort.
The wireless remote controller is the interface between the user and theriosystem. Commands are entered by the user to control the system. Any command that has been entered with the remote controller will remain in memory until it is changed by the user or the batteries are replaced.
When entering commands, point the remote controller in the direction of the LED display on the front panel. The indicator will appear for a short period of time on the remote controller when the command is entered. The unit will emit an audible beep when the signals are received correctly.
When the system is in OFF mode, the remote controller will display the time and last room setpoint. When you press the ON/OFF button, the unit will start in the last operating mode and room setpoint.
NOTE: If the ON/OFF button is pressed too soon after a stop, the compressor will not start for 3 minutes due to the inherent protection against frequent compressor cycling.
PRIVACY LOCK MODE
The Privacy Lock prevents unauthorized access to the unit controls and prevents tampering with system settings. The remote controller can be locked by pushing the "+" and "-" buttons simultaneously for 2 seconds. The Privacy Lock icon will be displayed on the remote controller. Repeat the process to unlock the remote controller.
Use the “MODE” button to select one of the available modes. The selected mode will be displayed on the remote controller and the appropriate light will illuminate on the display panel.
AUTO – Unit will automatically select heating or cooling tomaintain room temperature between 68°F and 77°F. The remote controller will display the Auto Mode icon with no setpoint. The front panel display will show "77."
COOL – To cool to selected setpoint and remove moisture. System varies compressor speed to maintain desired temperature.
HEAT – To heat to selected room setpoint. System varies compressor speed to maintaindesired room temperature
FAN ONLY – To circulate air without heating or cooling. Use Fan Speed button to selectspeed from low to high.
DRY – Select DRY MODE to increase moisture removal during warm humid conditions.
Room Temperature > Setpoint +4°F, the system will be operating in cooling mode with low fan speed.
Setpoint -4°F, < Room Temperature < Setpoint +4°F, the system will cycle 6 minutes ON and 4 minutes OFF in cooling mode. The indoor fan will be at low speed.
Room Temperature < Setpoint -4°F, the system will be OFF and the indoor fan will be at low speed.
VERTICAL SWING LOUVERS
Press the Vertical Swing Louver button to select five different vertical (up & down) air discharge directions including Continuous Sweep. The Vertical Swing Louver icon will be displayed. Press this button to set swing angle, which circularly changes as below: Indicates louver swings back and forth in the fiveplaces, as shown in the figure.
When operating in humid areas,riohas a DRY COILfunction called X-Fan that will allow the indoor fan to run for a pre-determined amount of time after the unit is turned off (cooling or dry modes) to ensure that additional moisture is removed from coil. Push the “X-FAN” button to enable this feature. The X-FAN icon will be displayed on remote controller. To deactivate this feature, push the “X-FAN” button again.
The desired setpoint, either in heating or cooling, can be achieved faster if TURBO mode is used. After selecting the “HEAT” or “COOL” mode button, push the “TURBO” button. The TURBO icon will be displayed on the remote controller and the unit will run at ultra high speed fan. To deactivate the feature, push the “TURBO” button again. The unit will return to normal operation.
The Rio can be programmed to automatically turn ON or OFF after a selected time period. Press TIMER button to activate the TIMER mode. In TIMER mode the HOUR ON/OFF icon will begin blinking.Press + or - button to select a time setting from 0.5 to 24 hours. Pressonce for slow adjustment and hold down for fast adjustment. Press TIMER button to confirm settings and HOUR ON/OFF icon will stopblinking. The unit will turn ON or OFF after the selected time period.
Theriowill automatically adjust room temperature during your sleep time. This slight change in temperature will not affect your comfort level due to the natural effects that sleeping has on the body, but it will save on energy consumption and will lower your electric bill. Press the SLEEP button to select Sleep Mode. The SLEEP icon will appear.
In Cool or Dry modes:
The unit will run at current room setpoint for 1 hour. After 1 hour, the setpoint will increase by 2° F. After 2 hours, the setpoint will increase by 4° F and maintain this setpoint until Sleep Mode is cancelled.
In Heat mode:
The unit will run at current room setpoint for 1 hour. After 1 hour, the setpoint will decrease by 2° F. After 2 hours, the setpoint will decrease by 4° F and maintain this setpoint until Sleep Mode is cancelled.
CHANGING BATTERIES AND ADDITIONAL NOTES
To change batteries, slide cover off battery compartment on back of remote controller. Remove and safely discard old batteries. Insert two new AAA 1.5V dry batteries, using correct polarity. Reattach back cover.
If the remote controller will not be used for a long time, remove batteries to prevent leakage damage.
Be sure to aim the remote controller at the receiver of the main unit when operating.
When remote emits a signal, icon will flicker; a tone will be heard when unit receives that signal.
Use the Manual Override button to manual operate the unit if the remote controller is lost or damaged. Lift up the front panel section on the indoor unit and locate the Manual Override button on the right hand side. Press the Manual Override button to turn ON the unit. The unit will operatein AUTO mode and will automatically select heating or cooling to maintain room temperature between 64°F and 77°F. The indoor fan will operate in auto fan mode. Press the Manual Overridebutton to cancel Manual Override Mode and transfer control back to the remote controller.
- Specification Sheet
- Data sheet
- Use & Care Instructions
- Service Manual
- Quick Start Guide
- Warranty Document
- Parts List
- Installation Instructions