Product Highlights
- Outdoor Condenser: MULTI30HP230V1BO
- Indoor Wall Mounted Units: CROWN09HP230V1AH, CROWN12HP230V1AH (x2)
- Wireless Remote Control (x3)
- Required, but not included: 1/4" x 1/2" line set (x2)
The GREE Multi21 Dual-Zone CROWN 30,000 BTU System is powered by GREE's energy efficient G10 inverter and a Variable Speed compressor. These units can heat and cool 3 zones without distribution boxes. Our G10 inverter technology saves energy, reduces outdoor noise and keeps room temperature steady by eliminating the harsh starts & stops of conventional systems.
Crown comes with easy-to-use Wireless Remote Controller with an large backlit display. In addition, Crown's built-in Wi-Fi technology allows direct local control from Smartphones with the Gree-Smart application, making it the most convenient choice for today's busy lifestyles.
Features & Benefits:
Outdoor Condenser
- High Efficiency up to 22 SEER
- G-10 Inverter Technology
- Sound Levels down to 56 dB(A)
- Multi-point Diagnostics
- Low Ambient Cooling down to 0°F
- Low Ambient Heating down to -4°F
- Intelligent Defrost
- Heavy Gauge Steel Cabinet
- Auto Restart on Power Outages
- Whisper Quiet down to 22 dB(A)
- Stainless Platinum Finish
- I-Feel Temperature Control
- 180° Vertical Air Supply
- 7 Fan Speeds
- 4-Way Airflow
- Smartphone Interface
- Intelligent Pre-Heating Power
- Power Failure Mode
- Wi-fi control - Allows direct local control from SmartPhones and tablets with the Gree-Smart app for a mobile lifestyle
- Wireless RF remote controller - Multi-functional hand-held RF wireless controller is sleek, ergonomically designed and easy to use with a large backlit LCD display.
- Multi-operational mode - The units can be set to five different operating modes: HEAT, COOL, DRY, FAN ONLY and AUTO.
- Timer - The unit may be programmed to turn ON or OFF after a selected time period. The time period can be adjusted between one half hour and 24 hours.
- I feel mode - Sense the room temperature from the remote control which is closest to you, instead of the indoor unit. This means that it will adjust for air ow and temperature for maximum personal comfort.
- Privacy lock mode - Wireless controllers feature a privacy lock to prevent unauthorized access that can tamper system settings.
- Sleep mode - The Crown has three sleep modes that automatically adjust the room's temperature during your sleep. The slight shift in temperature in these models will not affect your comfort level but it will significantly save in energy consumption.
- Fahrenheit F°/ Celsius C° - The wired and wireless controllers can be programmed to display the temperature reading in F° or C°.
Please Note: Mini Split Systems must be installed by a licensed Contractor with an EPA Refrigerant Certification to qualify for warranty.
Which line set kit do I need?
This system uses (2) 1/4" x 1/2" line set. These are sold separately, and you can choose from our 15 ft, 25 ft, 35 ft, 50 ft, and 75 ft lengths. The length needed depends on the needs of your project and how you will set up the system (distance from outdoor condenser to indoor air handler).
Can I install this myself?
While installation of a ductless split is much easier than a central air system, it's still much more advanced than installing a window unit or portable. Furthermore, the manufacturer warranty is only valid if a licensed professional does the installation. So while it is possible to do the installation yourself, we strongly recommend you hire an HVAC professional in your area.
Is this backed by a warranty?
Yes, it comes fully backed by a manufacturer's warranty, and ComfortUp is an authorized online seller of these systems. Our Customer Care Team will provide assistance should you ever need to file a warranty claim with the manufacturer. Please be aware that only systems that are installed by a licensed HVAC contractor are backed by the warranty. Proof of licensed installation is required. The receipt/invoice from your contractor should be sufficient.
Manuals & Docs
- Service Manual
- Installation Instructions
- Consumer Literature
- Parts List
- Submittal Sheet
- Warranty Document
- Submittal Sheet
- Use & Care Instructions
- Warranty Document
- Specification Sheet
- Quick Start Guide
- Installation Instructions
- Service Manual
Brand | GREE |
---|---|
Rated Heating Capacity (BTU) | 8189-32414 |
HSPF (Heating Seasonal Performance Factor) | 10.2 |
Nominal Capacity (BTU) | 30,000 |
Minimum Circuit Amps | 19 |
Liquid/Gas Line Set Size | 1/4" x 1/2" |
Number of Zones/Rooms | 3 Zones |
Maximum Fuse Size | 30 |
Rated Cooling Capacity (BTU) | 8189-33438 |
Wireless | Yes |
Efficiency | High |
4-Way Remote Air Flow Control | Yes |
Filter Type | Washable |
Phase | Single |
Sound Pressure Rating | 59 dB(A) |
Voltage | 208-230 VAC |
Inverter Technology | Yes |
Warranty Offered | 7 Year Compressor - 5 Year Parts to Original Registered End-User with Proof of Proper Installation |
Equipment Type | Heat Pump |
Model Family | MULTI 21 |
SEER | 21 |
Energy Star Rated | No |
Color | Stainless Platinum Finish |
Mounting Type | Wall |
EER (Energy Efficiency Ratio) | 12.0 |
Cycle/Hertz | 60 |
Corrosion Protection | Yes |
Refrigerant | R-410a |
Tonnage | 2 1/2 |
Product Family | MULTI 21 |
Room Size | 1,000 - 1,650 ft2 |
Remote Controller
Part Name
- ON/OFF Button
- +/- Button
- Cool Button
- Heat Button
- Fan Button
- I Feel Button
- Up & Down Swing Button
- Mode Button
- Timer-On Button
- Left & Right Swing Button
- Clock Button
- Timer-Off Button
- Sync Button
- Prog Button
- Light Button
- X-Fan Button
- Sleep Button
- WiFi Button
INTRODUCTION FOR ICONS ON DISPLAY SCREEN
MATCHING INSTRUCTIONS
The Crown models require the wireless remote controller to be matched to the indoor wall unit before beginning any operations, otherwise the Crown indoor wall unit will not accept commands from the remote controller. Follow the instructions below to automatically match the remote controller to the Crown indoor wall unit:
- Turn on electrical power to the Crown indoor and outdoor units. The Crown indoor wall unit will power up in Off (or Standby) mode.
- Hold the remote controller 5 to 6 feet from the Crown indoor wall unit.
- Point the remote controller at the Crown indoor wall unit and press the "Sync" button for 3 seconds.
- The Crown indoor wall unit will provide 3 beeps to signal a successful match.
- Press the Power ON button on the remote controller. The green indicator light will display on the Crown indoor wall unit.
- The remote controller is matched and ready for use.
If the Crown indoor unit and remote controller fail to match, then check the remote controller batteries, move closer and repeat the matching process again.
NOTE: This is a one-time requirement only. The remote controller and Crown indoor wall unit need to be successfully matched only once.
REMOTE CONTROLLER OPERATIONS
The wireless remote controller is sleek, versatile and allows you to change room temperatures and functions on your Crown system from the palm of your hand. The large LCD display and buttons make it easy-to-understand and easy-to-use.
The remote controller is set from factory to display temperatures in °F. If °C is desired, turn the remote controller OFF with the ON/OFF button and then press "MODE" and "––" buttons on the remote simultaneously for 5 seconds.
ON/OFF BUTTON
When the system is in OFF mode, the remote controller will display the time and last room setpoint. When you press the ON/OFF button, the unit will start in the last operating mode and room setpoint.
NOTE: If the ON/OFF button is pressed too soon after a stop, the compressor will not start for 3 to 5 min. due to the inherent protection against frequent compressor cycling.
LOCK MODE
The Privacy Lock prevents unauthorized access to the unit controls and prevents tampering with system settings. The remote controller can be locked by pushing the"+"and "-" buttons simultaneously for 5 seconds. The Privacy Lock icon will be displayed on the remote controller. Repeat the process to unlock the remote controller.
MODE BUTTON
Use the “MODE” button to select one of the available modes. The selected mode will be displayed on the remote controller and the appropriate light will illuminate on the front display panel.
-
AUTO – Unit will automatically select heating or cooling to maintain room temperature between 68°F and 77°F. The remote controller will display the Auto Mode icon with no setpoint. The front panel display will show "77."
COOL – To cool to selected setpoint and remove moisture. System varies compressor speed to maintain desired temperature.
HEAT – To heat to selected room setpoint. System varies compressor speed to maintain desired room temperature.
FAN ONLY – To circulate air without heating or cooling. Use Fan Speed button to select speed from low to high.
DRY – Select DRY MODE to increase moisture removal during warm humid conditions.
-
If the Room Temperature is more than 4°F above the set temperature, the system will be operating in cooling mode with low fan speed.
-
If the Room Temperature is between 4°F higher than, and 4°F less than, the set temperature, the system will cycle 6 minutes
ON and 4 minutes OFF in cooling mode. The indoor fan will be at low speed. -
If the Room Temperature is more than 4°F below the set temperature, the system will be OFF and the indoor fan will be at low speed.
-
VERTICAL SWING LOUVERS
-
Press the Vertical Swing Louver button to select five different vertical (up & down) air discharge directions including Continuous Sweep. The Swing Louver
icon will be displayed. Press this button to set swing angle, which changes in direction as below:
Indicates louver swings back and forth in the five directions, as shown.
HORIZONTAL SWING LOUVERS
-
Press the Horizontal Swing Louver button to select five different horizontal (left & right) air discharge directions including Continuous Sweep. The Horizontal Swing Louver icon will be displayed. Press this button to set swing angle, which changes in direction as below:
SLEEP MODE
The Crown system will automatically adjust room temperature during your sleep time. This slight change in temperature will not affect your comfort level due to the natural effects that sleeping has on the body, but it will save on energy consumption and will lower your electric bill. The Crown System has four Sleep Modes to select from. Press the SLEEP button to select Sleep 1, Sleep 2, Sleep 3, Sleep 4 modes or Cancel. The SLEEP icon will appear.
TRADITIONAL MODE - SLEEP 1
In Traditional Mode the unit will slowly relax the room set temperature by up to 4° F until Sleep Mode is cancelled.
TRADITIONAL MODE - SLEEP 2
In Expert Mode the unit will adjust the room set temperature at a rate based on the starting set temperature value. Sleep Mode will continue until cancelled.
DIY MODE - SLEEP 3
You will be required to enter eight (8) room setpoint values for eight (8) hours of run time. The last room setpoint value will be maintained until sleep mode is cancelled.
In Sleep Mode 3, press "Prog" button to enter setup mode. The remote controller will display “1:00” in the time location. Use the “+” and “-“ buttons to select the desired room setpoint for the first hour of run time. Then press the “Prog” button to save the setpoint.
The remote controller time display will change to “2:00.” Once again, use the “+” and “-“ buttons to select the desired room setpoint for the second hour of run time, and press the “Prog” button to again save the setpoint.
Repeat this sequence for the eight (8) room setpoint values. After all eight (8) values have been entered, the remote controller will automatically revert to standard time and temperature display, and the Sleep 3 Mode will begin.
At any time, you may press the “ON/OFF," " Mode," " Timer," "Sleep” or “Turbo" buttons to cancel the Sleep 3 Mode.
NOTE: During this procedure, if no button is pressed within 10 seconds, remote controller will automatically exit the sleep curve setting and resume original display. If ON/OFF, MODE, TIMER, SLEEP, COOLING or HEATING button is pressed during the setting or inquiry procedure, remote controller will also exit the sleep curve setting.
SIESTA MODE - SLEEP 4
In Siesta Mode the Crown System will automatically change the room temperature every 30 minutes based on the room temperature setting. Sleep Mode will continue until cancelled.
NOTE: function will be disabled if the air conditioner is restarted after power failure; Sleep function can not be set in AUTO mode.
I FEEL MODE
Press this button to use the I FEEL function, and the () icon will be displayed. The unit will sense room temperature at the remote controller instead of at the indoor unit. It then adjusts airflow and temperature accordingly for the ultimate in personal comfort control and energy savings. Press the button again to exit this function. For best performance, keep remote controller away from heat or cold temperature sources while using this function.
LIGHT BUTTON
Press this button to turn off display light on indoor unit. Press again to turn it back on.
WiFi BUTTON
Press and hold this button for three seconds to turn WiFi function on or off. See "Operation of Smart Control" section for more information
X-FAN MODE
When operating in humid areas, the unit has a DRY COIL function called X-Fan that will allow the indoor fan to run for a pre-determined amount of time after the unit is turned off (cooling or dry modes) to ensure that additional moisture is removed from coil. Push the “X-FAN” button to enable this feature. The X-FAN icon will be displayed on remote controller. To deactivate this feature, push the “X-FAN” button again.
DISPLAYING SETPOINT ON FRONT PANEL
Only the setpoint temperature will be displayed on the front panel and on the remote controller.
TURBO MODE
The desired room setpoint can be achieved faster in TURBO mode. After selecting the “HEAT” or “COOL” mode button, push the “TURBO” button. The TURBO icon will be displayed on the remote controller and the unit will run at an ultra-high speed. To deactivate the feature, push the “TURBO” button again. The unit will return to normal operation.
TIMER SETTING
T-ON button (Timer ON)
To set when you want the unit to turn On at the end of a selected time period, use the button labeled “T-ON” on the remote controller. Press this button to make the clock icon disappear, replaced with the word “ON” (blinking). Press “+” or“-” buttons to adjust timer setting 1 minute at a time. Press and hold “+” or “-” button to set timer more quickly. Press“T-ON” button again to confirm setting, and the word “ON” will stop blinking. To cancel, press“T-ON” button again.
T-OFF button (Timer OFF)
To set when you want the unit to turn Off at the end of a selected time period, use the button labeled “T-OFF” on the remote controller. Press this button to make the clock icon disappear, replaced with the word “OFF” (blinking). Adjust settings the same as with “T-ON” settings.
NOTE: Under Timer On and Off status, you can set T-ON and T-OFF simultaneously. Before setting timer, be sure to set clock to correct time.
CLOCK SETTING
Press this button to set clock time.“” icon on remote controller will blink. Within 5 seconds, press “+” or “-” button to set clock time. With each pressing of “+” or “-” buttons, clock time will increase or decrease 1 minute. To quickly adjust time setting, press and hold “+” or “-” button for 2 seconds. Release button when you have reached the desired time setting. Press “CLOCK” button to confirm the time, and “” icon will stop blinking.
NOTE: Clock time adopts 24-hour mode. A 12-hour time format is not available.
FAN BUTTON
Press the FAN button to adjust the fan circulation indoor speed: Low ( ) Low-Medium (
), Medium (
), Medium-High (
), High (
), Turbo (
), Auto and Quiet (
),
NOTE: Turbo function is not available in Dry and Auto Modes. The Crown unit will select proper fan speed automatically according to ambient temperature.
CHANGING BATTERIES AND ADDITIONAL NOTES
To change batteries, slide cover off battery compartment on back of remote controller. Remove and safely discard old batteries. Insert two new AAA 1.5V dry batteries, using correct polarity. Reattach back cover.
NOTE:
- If the remote controller will not be used for a long time, remove batteries to prevent leakage damage.
- Be sure to aim the remote controller at the receiver of the main unit when operating.
- When remote emits a signal, icon will flicker; a tone will be heard when unit receives that signal.
CHANGING BATTERIES
DAMAGED OR LOST REMOTE CONTROLLER
If remote controller is lost or damaged, the Crown system can be turned off directly from the indoor unit. Lift the front panel of the indoor wall unit, then press the AUX button to turn on or turn off. When the unit is on, it will operate in AUTO Mode.
NOTE: During this procedure, if no button is pressed within 10 seconds, remote
controller will automatically exit the sleep curve setting and resume original display.
If ON/OFF, MODE, TIMER, SLEEP, COOLING or HEATING button is pressed during the
setting or inquiry procedure, remote controller will also exit the sleep curve setting.
Sleep function will be disabled if the air conditioner is restarted after power failure;
Sleep function can not be set in AUTO mode.
CHANGING BATTERIES AND ADDITIONAL NOTES
To change batteries, slide cover off battery compartment on back of remote controller. Remove and safely discard old batteries. Insert two new AAA 1.5V dry batteries, using correct polarity. Reattach back cover.
NOTE:
- If the remote controller will not be used for a long time, remove batteries to prevent leakage damage.
- Be sure to aim the remote controller at the receiver of the main unit when operating.
- When remote emits a signal, icon will flicker; a tone will be heard when unit receives that signal.
CHANGING BATTERIES
DAMAGED OR LOST REMOTE CONTROLLER
If remote controller is lost or damaged, the Vireo system can be turned off directly from the indoor unit. Lift the front panel of the indoor wall unit, then press the AUX button to turn on or turn off. When the unit is on, it will operate in AUTO Mode.